Plaster calculator: how many bags do I need
Enter the wall or ceiling area, the coat and the thickness to see how many 25kg bags to buy, using British Gypsum's published coverage for Thistle plasters.
Plaster needed
Based on British Gypsum's published coverage. Uneven walls, deep patches and waste use more, so check with your supplier or plasterer.
How the plaster calculation works
British Gypsum publishes the area one 25kg bag covers at a stated thickness on each product's data sheet. The calculator works out the area to plaster, takes off doors and windows, and divides by that coverage figure. The answer is rounded up to whole bags, because plaster is sold by the bag.
A worked example: a bedroom with four walls adding up to 14m in length and a 2.4m ceiling has 14 x 2.4 = 33.6 m² of wall. Taking off a door and a window totalling 3.5 m² leaves 30.1 m². Thistle MultiFinish covers 10 m² per bag at 2mm, so a skim coat needs 30.1 / 10 = 3.01 bags, rounded up to 4 bags. Replastering the same walls with an 11mm HardWall undercoat needs 30.1 / 3 = 10.03, so 11 bags of HardWall plus the 4 bags of MultiFinish on top.
When a thickness other than the published one is entered, the coverage is scaled in proportion from the nearest published figure. For example, MultiFinish at 3mm is estimated at 10 x 2 / 3 = 6.67 m² per bag. This is an estimate, and the result says so when it is used.
What changes the result
The coat and the plaster
A finish or skim coat is thin, so one bag goes a long way: 10 m² for MultiFinish at 2mm. Undercoats are much thicker. HardWall covers 3 m² per bag at 11mm and BondingCoat 2.75 m² at 11mm, or 3.5 m² at 8mm on ceilings. A full replaster therefore uses several times more plaster than a skim.
Thickness
Doubling the thickness roughly halves the coverage. British Gypsum's data sheet gives 2mm for MultiFinish on walls and ceilings, and its installation guidance says the two coats together should be at least 2mm. BondingCoat's data sheet gives 11mm for walls and 8mm for ceilings.
The background
The surface under the plaster decides which undercoat is suitable. British Gypsum describes HardWall as an undercoat for most masonry and BondingCoat as suited to low-suction backgrounds. Old, uneven or patched walls take more plaster than a flat surface, because hollows have to be filled.
Walls or ceilings
For a ceiling, enter the room's length and width as the area. Ceilings are harder work than walls, which is one reason many homeowners leave them to a plasterer even when they skim walls themselves.
Common mistakes and tips
- Forgetting to deduct openings. Doors, windows and built-in units can take several square metres off a room.
- Mixing up the coats. A full replaster needs both an undercoat and a finish, so tick the extra MultiFinish coat when an undercoat is chosen.
- Buying too early. Gypsum plaster has a limited shelf life and the bags carry a use-by date, so buy close to when the work will be done.
- Mixing too much at once. MultiFinish starts to set within the working time on the bag, so mix what can be applied before it goes off.
- Plastering over the wrong surface. Painted, glossy or very smooth surfaces often need a bonding treatment first, which the product guidance explains.
When to get a professional
Skimming a small wall is a common first DIY plastering job, but getting a flat, smooth finish across a whole room or a ceiling takes practice. Full replasters, damp-damaged walls, old lath and plaster and anything that needs the background checking are best left to an experienced plasterer, who will also choose the right undercoat and order the materials.
Want a smooth finish first time? Compare well reviewed plasterers in your area.
Find a top rated plasterer near youHow this is worked out
- Area (m²) = total wall length x height (or the area entered) minus doors and windows.
- Coverage per bag = the published coverage at the published thickness. At another thickness: published coverage x published thickness / chosen thickness, from the nearest published point.
- Bags = area / coverage per bag, rounded up. Each bag is 25kg.
| Plaster (25kg bag) | Published coverage |
|---|---|
| Thistle MultiFinish (finish or skim coat) | 10 m² at 2mm |
| Thistle HardWall (undercoat for most masonry) | 3 m² at 11mm |
| Thistle BondingCoat (undercoat for low-suction backgrounds) | 3.5 m² at 8mm, 2.75 m² at 11mm |
- British Gypsum, Product Data Sheet: Thistle MultiFinish (dated 9 September 2022, checked 9 November 2026). Coverage per 25kg bag of 10 m² at 2mm thick; 2mm application thickness on walls and ceilings.
- British Gypsum, Installation guidance: Thistle MultiFinish (December 2021, checked 9 November 2026). Applied in two coats, with a total thickness for both coats of at least 2mm; about 11.5 litres of water per 25kg bag.
- British Gypsum, Product Data Sheet: Thistle HardWall (dated 9 September 2022, checked 9 November 2026). Coverage per 25kg bag of 3 m² at 11mm thick.
- British Gypsum, Product Data Sheet: Thistle BondingCoat (dated 9 September 2022, checked 9 November 2026). Coverage per 25kg bag of 3.5 m² at 8mm and 2.75 m² at 11mm; 11mm on walls and 8mm on ceilings; for low-suction backgrounds.
Related guides
Plaster quantity questions
How many bags of plaster do I need to skim a room?
Work out the area of the walls (length of all the walls added together, times the height, less doors and windows) and divide by 10, because British Gypsum gives 10 m² per 25kg bag of Thistle MultiFinish at 2mm. A room with 14m of wall 2.4m high and 3.5 m² of openings has 30.1 m², which needs 3.01 bags, so 4 bags.
How much does a bag of MultiFinish cover?
British Gypsum's data sheet gives 10 m² per 25kg bag at 2mm thick. Its installation guidance says MultiFinish goes on in two coats with a total thickness of at least 2mm. A thicker finish covers less, roughly in proportion to the thickness.
How much does a bag of HardWall cover?
British Gypsum gives 3 m² per 25kg bag of Thistle HardWall at 11mm thick. A wall of 30 m² therefore needs 10 bags of HardWall, plus 3 bags of MultiFinish to finish it at 2mm.
What is the difference between HardWall and BondingCoat?
Both are British Gypsum undercoat plasters. HardWall is described as an undercoat for most masonry, while BondingCoat is for low-suction backgrounds. BondingCoat covers 3.5 m² per 25kg bag at 8mm or 2.75 m² at 11mm, and its data sheet gives 11mm for walls and 8mm for ceilings. The right choice depends on the background, so a plasterer should check it first.
Should I buy extra plaster?
The bag counts here are rounded up to whole bags but include no extra for waste, uneven walls or deep patches. Hollows and uneven backgrounds use more plaster than the published coverage, so check the walls and talk to the supplier or plasterer before ordering a large quantity.
Rather leave it to a professional? Compare well reviewed plasterers near you.